Even though the ArmaLaser Small Block for the little Kel-Tecs
  only weighs 1.2 ounces with batteries installed on your pistol, it is..

TOUGH

  RELIABLE

  ACCURATE

  IMMEDIATE

Can
  any other polymer laser system boast these facts?

  Why we don’t like pressure
  switches for polymer pistols.

PRESSURE
  SWITCHES ARE NOT TRUE-TOUCH ACTIVATION.
  

Pressure
  switches are fine and dandy when you can imbed them into a rubber or plastic
  grip panel. The problem is that you can’t imbed a pressure switch onto
  most polymer pistols that don’t have a changeable back-strap. So you’re
  stuck putting all components ON TOP OF THE GRIP.

The penalty to
  this is different grips levels and pressure. One finger is on another level
  than the rest, and also needs to be squeezed in order to turn the laser on.

Bottom
  line:
  They feel weird. And they
  inhibit the natural movement of the most important finger on a pistol grip -
  THE RING FINGER!

  (300 x 175 pixel picture here)

Quick
  accurate shots and handling of your pistol relies on your ring finger. If that
  finger has to do the job of moving a pressure switch AND feels akward, you won’t
  be doing your groups or your self-defense training any favors.

The
  ring finger is so important for control especially in smaller pistols where
  you can’t get more than 2 fingers on the grip.

  The ArmaLaser actuation is effortless, comfortable, and done without you needing
  to THINK
  ABOUT IT.

  It
  takes laser actuation to the trigger finger where it belongs and OFF
  OF THE GRIP.

  

The
  shorter the grip, the more awkward a pressure switch on top of the grip feels.

See
  this video link to YouTube showing a Kel-Tec P3AT with an ArmaLaser SMALL BLOCK
  BEING DROPPED MUZZLE-FIRST FROM A 10 FOOT LADDER ONTO A CONCRETE FLOOR 100 TIMES.

(place this link
  in. Place a small link here with the YouTube logo-not sure how they do this
  but I've seen them on different sites I will change it later but at least we
  can see the layout:

  http://www.youtube.com/watch?v=_Xx2rjknDoE)

The
  laser never shuts off once and the red dot doesn’t lose its zero!

Patented
  method:

Only
  the ArmaLaser SMALL BLOCK attaches directly INTO the Kel-Tec frame. You can bang
  on it with a hammer, you’re not going to get it to move! Back-pocket carry
  isn’t even an issue. Offers 100% no up/down movement.

Uses
  the side of the grip to offer 100% no left/right movement.

(300 x 175 pixel
  picture here)

Only
  the ArmaLaser SMALL BLOCK takes advantage of the natural indentation on the grip
  sides to stop movement 100%. And the design doesn’t add any width to the
  pistol itself.

Why
  4 batteries when we could have put in only 2?

The
  SMALL BLOCK wouldn’t be a SMALL BLOCK if
  we had

  opted for a more streamlined design by housing only 2 batteries.

We
  chose 4 batteries for these two reasons:

TO
  CREATE A BLOCKY OUTLINE

TO
  DOUBLE THE TIME NEEDED BETWEEN BATTERY CHANGES

(300 x 175 pixel
  picture here)

The
  ArmaLaser will run on only 2 batteries, however, We killed 2 birds with 1 stone
  by adding an extra battery compartment. This way, we got the block outline we
  wanted AND doubled the battery capacity.

THE
  BLOCK OUTLINE ISN’T ONLY FOR POCKET CARRY.

Take a look at
  the following picture. It shows how the blocky outline helps the DeSantis Nemesis
  pocket holster to create a more wallet-like look in your pocket. If it does
  that with the holster, imagine how it works when you don’t have a holster
  or if you are using a belt clip.

(300 x 175 pixel
  picture here)

Our
  block outline offers an anti-printing advantage.

A
  little bit more room allows us to add features that other can’t - like a master kill switch and hardened electronics that shows confidence in offering a 5 year warranty.

Upgrade
  Program:

Let’s
  say you buy an ArmaLaser for a Glock and then sell it and buy a Kahr or a Kel-Tec.
  You can send in your old ArmaLaser and for $29 we can rehouse the expensive
  electronics in a new polymer housing for your new model pistol.

Let’s
  say we make an improvement or offer a green laser version in the future. For
  a specified fee, you can upgrade your system to the newer one.

As
  an ArmaLaser owner, the experience doesn't end when we get your money like it
  is with many other companies. We have programs in place that will always help
  keep you protected even as technologies and your needs change.

GREAT
  HOLSTER SELECTION:

Take
  a look at the great P32 and P3AT holsters available from Don Hume Leather and
  DeSantis. You can order directly from us and get a holster that WAS DESIGNED
  AND MADE TO FIT YOUR KEL-TEC WITH ARMALASER.