Even though the ArmaLaser Featherweight Small Block for the little Kel-Tecs only weighs 1.2 ounces with batteries installed on your pistol, it is..

	ARMALASER THE OTHERS YES NO YES NO YES NO YES NO YES YES YES NO YES NO YES NO YES NO
TRUE TOUCH ACTIVATION
MASTER KILL SWITCH
6 HOURS OF RUN TIME
CUSTOM HOLSTERS FROM $29
EASY AND QUICK INSTALL
EASY AND QUICK INSTALL WHILE ANCHORING DIRECTLY INTO FRAME FOR ABSOLUTE ROCK-SOLID DO-IT-YOURSELF ATTACHMENT IN 5 MINUTES?
5 YEAR WARRANTY
UPGRADEABLE
TAKES ADVANTAGE OF BOTH THE P32/P3AT FRAME PIN AND GRIP FEATURES TO OFFER A SOLID 100% NO MOVEMENT ATTACHMENT?

Why we don’t like pressure switches for polymer pistols:

PRESSURE SWITCHES ARE NOT TRUE-TOUCH ACTIVATION.

Pressure switches are fine and dandy when imbedded into rubber or plastic grips where the depth of the switch can be hidden into the grip. The problem is that you can’t imbed a pressure switch onto most polymer pistols that don’t have a changeable back-strap. So you’re stuck putting all components
ON TOP OF THE GRIP.

The penalty to this is different grips levels and pressure. One finger is on another level than the rest, and also needs to be squeezed in order to turn the laser on.

Bottom line: They feel weird. And they inhibit the natural movement of the most important finger on a pistol grip -
THE RING FINGER!

Try an experiment: tape a thicker button cell battery on the grip of your pistol and ask yourself if that is comfortable to shoot or hinders your ability to grasp the pistol properly. I think you'll see then why our touch-activation technology is the key for pocket and sub-compact polymer pistols.

Quick accurate shots and handling of your pistol relies on your ring finger. If that finger has to do the job of moving a pressure switch AND feels akward, you won’t be doing your groups or your self-defense training any favors.

The ring finger is so important for control especially in smaller pistols where you can’t get more than 2 fingers on the grip.
The ArmaLaser actuation is effortless, comfortable, and done without you needing to THINK ABOUT IT.
It takes laser actuation to the trigger finger where it belongs and OFF OF THE GRIP.

The shorter the grip, the more awkward a pressure switch on top of the grip feels.

See this video link to YouTube showing a Kel-Tec P3AT with an ArmaLaser Featherweight SMALL BLOCK BEING DROPPED MUZZLE-FIRST FROM A 10 FOOT LADDER ONTO A CONCRETE FLOOR 100 TIMES. Remember this laser system only weighs 1.2 ounces with batteries installed on your pistol!

The laser never shuts off once and the red dot doesn’t lose its zero!

Patented method:

Only the ArmaLaser SMALL BLOCK attaches directly INTO the Kel-Tec frame. You can bang on it with a hammer, you’re not going to get it to move! Back-pocket carry isn’t even an issue. Offers 100% no up/down movement.

Uses the side of the grip to offer 100% no left/right movement.

Only the ArmaLaser SMALL BLOCK takes advantage of the natural indentation on the P32 & P3AT grip sides to stop movement 100%. And the design doesn’t add any width to the pistol itself.

Why 4 batteries when we could have put in only 2?

The SMALL BLOCK wouldn’t be a SMALL BLOCK if we had
opted for a more streamlined design by housing only 2 batteries.

We chose 4 batteries for these two reasons:

TO CREATE A BLOCKY OUTLINE

TO DOUBLE THE TIME NEEDED BETWEEN BATTERY CHANGES

The ArmaLaser will run on only 2 batteries, however, We killed 2 birds with 1 stone by adding an extra battery compartment. This way, we got the block outline we wanted AND doubled the battery capacity.

THE BLOCK OUTLINE ISN’T ONLY FOR POCKET CARRY.

Take a look at the following picture. It shows how the blocky outline helps the DeSantis Nemesis pocket holster to create a more wallet-like look in your pocket. If it does that with the holster, imagine how it works when you don’t have a holster or if you are using a belt clip.

Our block outline offers an anti-printing advantage.

A little bit more room allows us to add features that other can’t - like a master kill switch and hardened electronics that shows confidence in offering a 5 year warranty.

Upgrade Program:

Let’s say you buy an ArmaLaser for a Glock and then sell it and buy a Kahr or a Kel-Tec. You can send in your old ArmaLaser and for $29 we can rehouse the expensive electronics in a new polymer housing for your new model pistol.

Let’s say we make an improvement or offer a green laser version in the future. For a specified fee, you can upgrade your system to the newer one.

As an ArmaLaser owner, the experience doesn't end when we get your money like it is with many other companies. We have programs in place that will always help keep you protected even as technologies and your needs change.

GREAT HOLSTER SELECTION:

Take a look at the great P32 and P3AT holsters available from Don Hume Leather and DeSantis. You can order directly from us and get a holster that WAS DESIGNED AND MADE TO FIT YOUR KEL-TEC WITH ARMALASER.

Money Back Guaranteed for 30 days!